2N6489 DATASHEET PDF

0 Comment

2N 2N 2N DESCRIPTION. ·With TO package. ·Excellent safe operating area. ·Complement to type 2N 2N 2N respectively. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics. 2N datasheet, 2N circuit, 2N data sheet: MOSPEC – POWER TRANSISTORS(15A,75W),alldatasheet, datasheet, Datasheet search site for.

Author: Dujar Maukus
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Literature
Published (Last): 17 December 2012
Pages: 488
PDF File Size: 20.29 Mb
ePub File Size: 18.31 Mb
ISBN: 460-4-65817-120-9
Downloads: 46440
Price: Free* [*Free Regsitration Required]
Uploader: Samulkree

A partial list of companies is shown in Table Another variation of the half bridge is the split winding circuit shown in Figure D. Proportional Base Drive Figure Closer matching of the internal amplifier input transistors, minimizes this effect, as does selecting a feedback ratio, j8, to be close to unity.

Output currents in excess of mA can be obtained depending on input voltage, heatsinking and maximum ambient temperature. Spring Semester, Monday — Friday: E-C cores offer a performance advantage better coupling but standard E cores cost less and are also used in these applications. Once coCRl is found, the value of the filter capacitor, C, can be determined from: In order to simplify the design of the input supply see Section 8V IN is chosen to be 16V average with a 3V p-p ripple at full load and up to 25V at no load.

With a few passive components the MC is able to perform all of the monitoring required for a power supply. Search the history of over billion web pages on the Internet. At an input of 90 Vac, full-load output voltages are 4. This can cause poorer than expected load regulation in cases where the load currents are large or where the load is located some distance from the regulator.

2N6489 Datasheet

The input supply is now designed using the information contained in Section 8 and the regulator circuit is constructed using the guidelines given in Section 5. To prevent false tripping of the OVP circuit by noise which would not normally harm the load, MC has a programmable delay feature.

The faster Switchmode II and III bipolar products fall somewhere between the curves shown and therefore are more competitive with FET’s at the higher operating frequencies. The mounting surface should be flat, smooth, free of deep scratches datasheeet burrs, and free of paint, varnish, anodization, or oxidation. As the output current increases, the voltage drop across Rsc increases until Va and Vr2 are great enough to bias Q3 on.

TOP Related Posts  GISELLE BEIGUELMAN PDF

Study of the available regulators given vatasheet the selection guide of Section 17 reveals that both the MCC and MCI would meet the regulation performance requirements. Refer- ring to the MCI data sheet Section 18there are two package styles to choose from.

Here, typical power losses for 5.

(PDF) 2N6489 Datasheet download

This is because the 2n6849 size of a capacitor is dependent on its CV product, while energy storage is proportional to CV 2. Practical solutions to this problem include limiting the minimum load and using the right amount of filter capacitance to give the regulator time to respond to this change. For the single transistor versions, V turn-on and 1. The power supply is also very efficient.

In this figure, the regulator is modeled as a voltage source with a positive output impedance, Zo. It is not uncommon to have several hundred dollars worth of electronics supplied from a single low voltage supply.

As the name implies, the SCR is used 2nn6489 like a crowbar would be, to short the dc supply when an overvoltage condition is detected. The drive current determines both the rise and fall times for the drain current.

When filter capacitors are placed in series across the rectified line, as in a doubler circuit, voltage sharing can be a problem. Emitter-Base resistor in “PNP” type boost configuration too large 2.

2N power amplifier circuit datasheet & applicatoin notes – Datasheet Archive

They are available in a variety of positive or negative output voltages and current ranges. The time constant of this network should equal the anticipated switching time of the transistor ns to 1 fi-s.

This method is Figure Engineering Program is accredited by: Basic Pulse Width Modulator Control IC Features required datazheet a control IC vary to some extent because of the particular needs of a designer and on the circuit topology chosen. General Design Considerations It should be noted that all circuit configurations shown have constant current limiting; if foldback limiting is desired, see Section 4C for techniques and design equations.

TOP Related Posts  CORDIA ECALYCULATA PDF

Cref is chosen to be 0. Tj where 8ia Pd Iib Io solving for Io: The circuit shown in Figure senses the voltage on the power supply filter capacitors to predict the imminent power supply failure. If a sufficient number of half cycles are missing, or if the brownout continues for a sufficient time, the circuit will detect an ac line fault and output a line fault indication on the indicator output.

This can result in immediate destruction of the Datashet or gradual degradation of its forward blocking voltage capabilities, depending upon the severity of the occasion. Switching power supply components have actually evolved from components used in similar applications. The output voltage of this regulator can be any magnitude and is limited only by the capabilities of datasneet external transistor.

In comparing the two, note that the watt design is a half-bridge, while the 1, watt is a full bridge. Several positive regulators could be used with the same input supply to deliver several voltages with common grounds; negative regulators may be utilized in a similar manner. The unheatsinked MCCL is chosen since this approach is the least complex.

Basic Linear regulator theory and switching regulator topologies has been included along with practical design examples.

Since the control IC has an extra amplifier, the addition of a sense resistor and simple divider network to the high-current 5.

Also, current-limiting protection on any or all of the output windings is simplified. To aid in the selection of devices for this application, Motorola has characterized several devices specifically for crowbar applications. It turns out that FET’s can be directly coupled to many IC’s with only to mA of sink and source output capability and still switch efficiently at 20 kHz.